H3C交换机只能启动到BootWare扩展字段,无法启动到应用配置界面

tftpd64_v3.51前几天我公司售后技术员拿回几台H3C S5024PV2_EI交换机,所有交换机的故障都是无法进入应用系统配置界面,只能启动到BootWare扩展字段。在查找相关资料和拔打H3C售后服务电话后,得到相关资料和更新文件,在对所有交换机尝试做了更新固件的操作后,其中一台在烤机后故障排除,但其余几台烤机发现重启过后还是无法正常工作,只能返厂维修(H3C售后技术也是这样解释)。
        虽然刷新固件并没有把所有交换机都修复,但还是有一定概率修复机会的(修复一台)。下面我就把过程和方法分享给大家,希望对以后的工作有所帮助。

H3C S5024PV2_EI交换机启动故障如下:

****************************************************************************
*                                                                          *
*                 H3C S5024PV2-EI BootWare, Version 1.03                   *
*                                                                          *
****************************************************************************
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB

Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):

要更新固件,我们首先要把新的bin文件导入交换机内存中。所以我们要先把老的bin文件给删除,清空内存。方法如下:

Enter your choice(0-9): 4    ——这里选择4(文件控制)

Note:the operating device is flash

| |<1> Display All File(s)

| |<2> Set Application File type

| |<3> Set Configuration File type

| |<4> Delete File

| |<0> Exit To Main Menu

Enter your choice(0-4): 1   ——显示所有文件

Display all file(s) in flash:  ‘M’ = MAIN      ‘B’ = BACKUP      ‘S’ = SECURE      ‘N/A’ = NOT ASSIGNED
============================================================================

|NO. Size(B)                          Time                 Type   Name

| |1   11701248  Aug/08/2008 20:00:00 M      s5024pv2_ei-cmw520-r1103.bin      ——这是主文件

| |2   11701248  Aug/08/2008 20:00:00 B      s5024pv2_ei-cmw520-r1103_b~001    ——这是备份文件

| |3   1048544   Oct/25/2000 21:10:02 N/A    logfile/logfile.log      ——这是日志文件

Note:the operating device is flash

| |<1> Display All File(s)

| |<2> Set Application File type

| |<3> Set Configuration File type

| |<4> Delete File

| |<0> Exit To Main Menu                                                    
Enter your choice(0-4): 4  ——选择4,删除文件

Deleting the file in flash:  ‘M’ = MAIN      ‘B’ = BACKUP      ‘S’ = SECURE      ‘N/A’ = NOT ASSIGNED
|NO. Size(B)                         Time                 Type   Name

| |1   11701248  Aug/08/2008 20:00:00 M      s5024pv2_ei-cmw520-r1103.bin

| |2   11701248  Aug/08/2008 20:00:00 B      s5024pv2_ei-cmw520-r1103_b~001

| |3   1048544   Oct/25/2000 21:10:02 N/A    logfile/logfile.log

| |0   Exit                                                                 
Enter file No:1  ——选择1,主文件

The file you selected is flash:/s5024pv2_ei-cmw520-r1103.bin,Delete it? [Y/N ]Y  ——是否删除,选择Y
 Deleting………………………………………………………….. …………………………………………………………. ——删除中,请等待

Connection closed.

[END] 2018/4/9 13:00:12  ——提示删除完成

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3 ——选择3,进入网络子选项

==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Ethernet Parameter                                             |
|<0> Exit To Main Menu                                                     |
|<Ensure The Parameter Be Modified Before Downloading!>                    |
============================================================================
Enter your choice(0-5): 5 ——修改网络参数

==========================<ETHERNET PARAMETER SET>==========================
|Note:       ‘.’ = Clear field.                                            |
|            ‘-‘ = Go to previous field.                                   |
|          Ctrl+D = Quit.                                                  |
============================================================================
Protocol (FTP or TFTP) :tftp  ——默认使用协议
Load File Name         :host
                       :S5024PV2_EI-CMW520-R1111.bin   ——写入我们要更新的bin文件名称
Target File Name       :target
                       :S5024PV2_EI-CMW520-R1111.bin   ——这里一样
Server IP Address      :192.168.1.1  ——这是tftp服务器的地址,也就是本机电脑要设置的地址

Local IP Address       :192.168.1.253  ——这是交换机自动得到的地址
Gateway IP Address     :0.0.0.0

然后我把自己的笔记本网卡配置成192.168.1.1(这很简单不配图解),然后打开3CDaemon这个tftp软件,配置成tftp服务器:

图片.png

设置好上传目录,把要更新的bin文件也放在这个目录下:

图片.png

进入交换机配置界面进行文件上传:

==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Ethernet Parameter                                             |
|<0> Exit To Main Menu                                                     |
|<Ensure The Parameter Be Modified Before Downloading!>                    |
============================================================================
Enter your choice(0-5): 2   ——选择2,下载更新应用文件

Loading……………………………………………………………
………………………………………………………………….
………………………………………………………………….
………………………..Done!
12649472 bytes downloaded!  ——等一段时间后下载成功

Updating File flash:/S5024PV2_EI-CMW520-R1111.bin………………………
………………………………………………………………….
.Done!  —— 更新完成                 
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Ethernet Parameter                                             |
|<0> Exit To Main Menu                                                     |
|<Ensure The Parameter Be Modified Before Downloading!>                    |
============================================================================
Enter your choice(0-5): 0  ——退出到上一级菜单

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1 ——选择1,重启系统

Starting to get the main application
file–flash:/S5024PV2_EI-CMW520-R1111.bin!……………………………. ——加载更新后的bin文件
……………………………………………………..
The main application file is self-decompressing………………………..

……………………………Done!  ——主文件解压完成
System application is starting…  ——系统应用启动
Startup configuration file does not exist.
Configuring default settings.
User interface aux0 is available.

Press ENTER to get started.
<H3C>
#Apr 26 12:00:30:954 2000 H3C SHELL/4/LOGIN:
 Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1<hh3cLogIn>: login from Console
%Apr 26 12:00:31:094 2000 H3C SHELL/5/SHELL_LOGIN: Console logged in from aux0.
<H3C>                                       ———到这里是不是就是我们所熟悉的交换机配置界面了

所有步骤到这里就完成了,大家以后碰到此类问题可以自己尝试解决一下,实在不行再返厂维修。

窝窝素材网-一个免费分享各类素材资源的网站!
窝窝素材网 » H3C交换机只能启动到BootWare扩展字段,无法启动到应用配置界面

发表评论

提供最优质的资源集合

立即查看 了解详情